PIC18F4450T-I/ML【PDF 184/241 页】IC PIC MCU FLASH 8KX16 44QFN

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录3872

180页 181页 182页 183页 [184页]185页 186页 187页 188页

2010 Microchip Technology Inc.

DS70141F-page 47

dsPIC30F3010/3011

5.2

Reset Sequence

A Reset is not a true exception, because the interrupt

controller is not involved in the Reset process. The

processor initializes its registers in response to a

Reset, which forces the PC to zero. The processor then

begins program execution at location 0x000000. A

GOTO

instruction is stored in the first program memory

location, immediately followed by the address target for

the GOTO instruction. The processor executes the GOTO

to the specified address and then begins operation at

the specified target (start) address.

5.2.1

RESET SOURCES

There are 6 sources of error which will cause a device

reset.

Watchdog Time-out:

The watchdog has timed out, indicating that the

processor is no longer executing the correct flow

of code.

Uninitialized W Register Trap:

An attempt to use an uninitialized W register as

an Address Pointer will cause a Reset.

Illegal Instruction Trap:

Attempted execution of any unused opcodes will

result in an illegal instruction trap. Note that a

fetch of an illegal instruction does not result in an

illegal instruction trap if that instruction is flushed

prior to execution due to a flow change.

Brown-out Reset (BOR):

A momentary dip in the power supply to the

device has been detected, which may result in

malfunction.

Trap Lockout:

Occurrence of multiple trap conditions

simultaneously will cause a Reset.

5.3

Traps

Traps can be considered as non-maskable interrupts,

indicating a software or hardware error, which adhere

to a predefined priority as shown in Figure 5-1. They

are intended to provide the user a means to correct

erroneous operation during debug and when operating

within the application.

Note that many of these trap conditions can only be

detected when they occur. Consequently, the question-

able instruction is allowed to complete prior to trap

exception processing. If the user chooses to recover

from the error, the result of the erroneous action that

caused the trap may have to be corrected.

There are 8 fixed priority levels for traps: Level 8

through Level 15, which implies that the IPL3 is always

set during processing of a trap.

If the user is not currently executing a trap, and he sets

the IPL<3:0> bits to a value of ‘0111’ (Level 7), then all

interrupts are disabled, but traps can still be processed.

5.3.1

TRAP SOURCES

The following traps are provided with increasing

priority. However, since all traps can be nested, priority

has little effect.

Math Error Trap:

The math error trap executes under the following four

circumstances:

Should an attempt be made to divide by zero,

the divide operation will be aborted on a cycle

boundary and the trap taken.

If enabled, a math error trap will be taken when

an arithmetic operation on either accumulator A

or B causes an overflow from bit 31 and the

accumulator guard bits are not utilized.

If enabled, a math error trap will be taken when

an arithmetic operation on either accumulator A

or B causes a catastrophic overflow from bit 39

and all saturation is disabled.

If the shift amount specified in a shift instruction

is greater than the maximum allowed shift

amount, a trap will occur.

Note:

If the user does not intend to take correc-

tive action in the event of a trap error

condition, these vectors must be loaded

with the address of a default handler that

simply contains the RESET instruction. If,

on the other hand, one of the vectors

containing an invalid address is called, an

address error trap is generated.

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式